The baseline
A 2,000 sq ft code-built house in Hamden typically wants somewhere between 700 and 850 gallons of oil a year, or the propane, pellet or cord wood equivalent. That is the number a percentage saving has to be measured against.
Home / Service Area / Hamden, CT
Steel insulated panels in Hamden, CT.
Hamden builds for people who compare monthly cost, not sticker price — and who will own the result long enough for the heating bill to matter more than the framing invoice.
5AClimate zone
R-61Effective wall R-value
50%Less framing labour
75%Less heating energy
Suburban · New Haven County
What Hamden projects ask of a wall.
Subdivision and single-lot construction with good truck access, conventional foundations, and a resale market that reads the energy label. Additions and accessory dwellings are as common as new houses.
The arithmetic is straightforward here. A code-built house in this climate spends a large share of its life heating the outdoors through its own studs. A thermally broken panel wall at an effective R-51 to R-61 cuts heating energy by up to 75%, and the resulting load lets the mechanical system be sized at roughly half — money back at the start, not just over thirty winters.
What we typically supply in Hamden: custom homes, additions, accessory dwelling units, garages and heated workshops.
The arithmetic in zone 5A
What the wall is worth here, in fuel.
Zone 5A runs roughly 5,500 to 6,500 heating degree days — a long enough heating season that the envelope, not the equipment, sets what the building costs to run.
The same house in panels
At an effective R-51 to R-61 with the studs thermally broken from the exterior face, heating energy typically falls 70 to 75% — on the order of 189 to 255 gallons. At current delivered prices that is thousands of dollars a year, every year the building stands.
The upfront return
A design load that low lets the mechanical system be sized at roughly half. Smaller equipment, smaller ductwork, less dedicated electrical service, and on solar-paired projects a smaller array and battery bank. That money never leaves the construction budget.
Baselines are typical for the climate zone and floor area, not a promise about your building. Send plans and we will run the numbers on the actual design.
Four products, one panel
Structure, insulation, sheathing and vapour barrier arrive together.
Each panel bonds light gauge galvanised steel structural members to EPS with a patented composite joining technology, and does the work of four separate trades. That is why the framing phase for an average house is about three days rather than three weeks.
Exterior wall panel
5.5″ or 7.5″ thick, up to 4′ × 12′, effective R-51 to R-61, up to 42,000 plf LRFD, ready for direct application of the final cladding.
Roof panel
Load bearing, so trusses open to every 4–6 ft. Two panels connect at the ridge for cathedral ceilings and A-frames with no intermediate support.
Interior and ceiling panels
3.5″ at R-28 for partitions, tiny homes and quiet rooms; ceiling panels pre-chased and ready for direct sheathing.
Floor and below-grade
Concrete floor panels span up to 50 ft with minimal shoring and cut concrete volume by around 40%; below-grade panels are rated for foundation and retaining walls.
How it works
Four steps from a Hamden sketch to a finished shell.
01
Send what you have
Architect’s drawings, a plan-service set, or a hand sketch with rough dimensions and a note about storeys and roof. We will tell you what is missing.
02
Free take-off and price
We panelize the building on paper and return a package and a delivered price to your Hamden site — no cost, and an honest comparison against building it the usual way.
03
Shop drawings
Two to four weeks. Our drafters work with your architect and engineer: every panel numbered, every rough opening located, beams and headers integrated.
04
Delivery and assembly
Panels arrive bundled in wall-line order with track, screws and hardware. One framer and two helpers close in an average house in about three days.
Code and compliance in Connecticut
Your plan reviewer has seen this before.
The Connecticut State Building Code and its energy provisions are met comfortably by a documented effective R-51 to R-61 assembly, without exterior continuous insulation.
Structural
IAPMO load tables for construction types II–V, signed and sealed by BEI Engineering. Up to 42,000 plf LRFD in bearing and 2,420 plf in shear with a 2.0 safety factor.
Fire and acoustics
Two-hour load-bearing, one-hour load-bearing and two-hour non-load-bearing assemblies. EPS smoke and flame spread, self-ignition and flash ignition data. STC-rated assemblies for party walls.
Envelope and weather
Intertek thermal performance assessment, thermal zone map, ASTM E283, E331 and E330 air and water penetration testing, HUD Bulletin 1072 compliance and documented manufacturing tolerances.
Questions from Hamden
Straight answers before you commit.
Will this help resale?
A documented R-51 to R-61 envelope and a heating bill a quarter of the neighbours’ is an unusually concrete thing to put in a listing, and buyers in this market have learned to ask.
Can I add on to an existing house with panels?
Yes. Matching an existing structure is a drawing problem, and the addition ends up better insulated than what it attaches to — which is usually the point.
Do I need a special builder?
No. Your own framer, in almost every case. Training runs under two hours for a crew that has framed before, and the only power tool required is a screw gun.
Do you really deliver to Hamden?
Yes. We supply the whole of New England from our base in Keene, New Hampshire, with panels manufactured in Radford, Virginia. Freight to Hamden is a quoted line item on the estimate, not a surprise at the end, and it is a small number against what the wall saves over the life of the building.
Is it more expensive than building with lumber?
The panel package costs more than a lumber package. The finished wall usually costs less, because the panel replaces framing, insulation, sheathing and vapour barrier and cuts framing labour by roughly half — then the mechanical system shrinks by about 50%. We will price it both ways so you can see the whole picture rather than one line of it.
How do I get a price for my Hamden project?
Send plans, a sketch or a description with rough dimensions to our team. You get a panel take-off and a delivered price at no cost, usually within a few days, plus a note on anything in the design that is fighting the system while it is still cheap to change.
Building in Hamden? Let’s price it.
Plans, a sketch or a napkin. We will tell you what the panel package costs delivered to your site — and what it saves against stick framing.