The baseline
A 2,000 sq ft code-built house in Montpelier typically wants somewhere between 850 and 1000 gallons of oil a year, or the propane, pellet or cord wood equivalent. That is the number a percentage saving has to be measured against.
Home / Service Area / Montpelier, VT
Steel insulated panels in Montpelier, VT.
A small capital with state work, a strong preservation ethic and a flood history that has made resilience a real design criterion.
6AClimate zone
R-61Effective wall R-value
50%Less framing labour
75%Less heating energy
Institutional · Washington County
What Montpelier projects ask of a wall.
Winooski River floodplain constraints, historic downtown, hillside lots.
The lifecycle case is unusually easy to make in writing: a 425-year material life expectancy, a non-combustible assembly with two-hour fire-rated load-bearing tests, zero-waste manufacturing, 100% recyclability and an operating load 70–75% below a code building. The manufacturer is registered on SAM.gov and supplies government and military projects internationally.
What we typically supply in Montpelier: State and institutional buildings, flood-resilient replacement housing, in-fill.
The arithmetic in zone 6A
What the wall is worth here, in fuel.
Zone 6A runs roughly 7,000 to 8,000 heating degree days. A code-minimum wall spends a large share of that season conducting heat straight through its own framing.
The same house in panels
At an effective R-51 to R-61 with the studs thermally broken from the exterior face, heating energy typically falls 70 to 75% — on the order of 230 to 300 gallons. At current delivered prices that is thousands of dollars a year, every year the building stands.
The upfront return
A design load that low lets the mechanical system be sized at roughly half. Smaller equipment, smaller ductwork, less dedicated electrical service, and on solar-paired projects a smaller array and battery bank. That money never leaves the construction budget.
Baselines are typical for the climate zone and floor area, not a promise about your building. Send plans and we will run the numbers on the actual design.
Four products, one panel
Structure, insulation, sheathing and vapour barrier arrive together.
Each panel bonds light gauge galvanised steel structural members to EPS with a patented composite joining technology, and does the work of four separate trades. That is why the framing phase for an average house is about three days rather than three weeks.
Exterior wall panel
5.5″ or 7.5″ thick, up to 4′ × 12′, effective R-51 to R-61, up to 42,000 plf LRFD, ready for direct application of the final cladding.
Roof panel
Load bearing, so trusses open to every 4–6 ft. Two panels connect at the ridge for cathedral ceilings and A-frames with no intermediate support.
Interior and ceiling panels
3.5″ at R-28 for partitions, tiny homes and quiet rooms; ceiling panels pre-chased and ready for direct sheathing.
Floor and below-grade
Concrete floor panels span up to 50 ft with minimal shoring and cut concrete volume by around 40%; below-grade panels are rated for foundation and retaining walls.
How it works
Four steps from a Montpelier sketch to a finished shell.
01
Send what you have
Architect’s drawings, a plan-service set, or a hand sketch with rough dimensions and a note about storeys and roof. We will tell you what is missing.
02
Free take-off and price
We panelize the building on paper and return a package and a delivered price to your Montpelier site — no cost, and an honest comparison against building it the usual way.
03
Shop drawings
Two to four weeks. Our drafters work with your architect and engineer: every panel numbered, every rough opening located, beams and headers integrated.
04
Delivery and assembly
Panels arrive bundled in wall-line order with track, screws and hardware. One framer and two helpers close in an average house in about three days.
Code and compliance in Vermont
Your plan reviewer has seen this before.
Vermont’s Residential Building Energy Standards and its stretch code are among the most demanding in the country. A thermally broken panel at effective R-51 to R-61 clears them without adding a layer of exterior insulation.
Structural
IAPMO load tables for construction types II–V, signed and sealed by BEI Engineering. Up to 42,000 plf LRFD in bearing and 2,420 plf in shear with a 2.0 safety factor.
Fire and acoustics
Two-hour load-bearing, one-hour load-bearing and two-hour non-load-bearing assemblies. EPS smoke and flame spread, self-ignition and flash ignition data. STC-rated assemblies for party walls.
Envelope and weather
Intertek thermal performance assessment, thermal zone map, ASTM E283, E331 and E330 air and water penetration testing, HUD Bulletin 1072 compliance and documented manufacturing tolerances.
Questions from Montpelier
Straight answers before you commit.
What happens to the assembly in a flood?
Steel and EPS do not rot or delaminate when wet, which is a meaningful difference from wood framing or OSB-faced panels.
Can you build elevated first floors?
Yes, and below-grade rated panels are available for foundation and retaining conditions.
Are you set up for public procurement?
The manufacturer is SAM.gov registered and has supplied government and military projects in multiple countries. HUD Bulletin 1072 compliance and manufacturing tolerance documentation against HUD requirements are both published.
What lifecycle numbers can we cite?
A 425-year material life expectancy, non-combustible assembly, 100% recyclable at end of life, zero-waste manufacturing with recycled content, and operating energy 70–75% below a code-built equivalent.
What documentation comes with a bid?
Sealed load tables, fire and STC test reports, ASTM air and water penetration testing, thermal performance assessment, connection details in PDF and AutoCAD, and the specification sheet. All of it is public on our resources page.
Do you really deliver to Montpelier?
Yes. We supply the whole of New England from our base in Keene, New Hampshire, with panels manufactured in Radford, Virginia. Freight to Montpelier is a quoted line item on the estimate, not a surprise at the end, and it is a small number against what the wall saves over the life of the building.
Is it more expensive than building with lumber?
The panel package costs more than a lumber package. The finished wall usually costs less, because the panel replaces framing, insulation, sheathing and vapour barrier and cuts framing labour by roughly half — then the mechanical system shrinks by about 50%. We will price it both ways so you can see the whole picture rather than one line of it.
How do I get a price for my Montpelier project?
Send plans, a sketch or a description with rough dimensions to our team. You get a panel take-off and a delivered price at no cost, usually within a few days, plus a note on anything in the design that is fighting the system while it is still cheap to change.
Building in Montpelier? Let’s price it.
Plans, a sketch or a napkin. We will tell you what the panel package costs delivered to your site — and what it saves against stick framing.